7mm Mickoo's Commercial Workbench

mickoo

Western Thunderer
I’m sure you know, but just in case, mount it so the back jaw is outboard of the edge of the bench.

Handy for filing the end of long things...

Atb
Simon
Indeed, it's not permanently fixed here, just G clamped in place, to fix it with the rear jaw over the bench will result in the front end overhanging and smacking my leg every time I walk past; that's what I liked with the smaller vice, it has a steel shoe fitted on the desk and you can slide it on and off and clamp it in place.

It's primary use will be for taking the cusp off large pieces, not beating large bits of metal around, it's probably almost heavy enough not to need fixing for it's intended use, though I suspect the more it gets used the more I'll find ways to abuse it.
 

mickoo

Western Thunderer
Nothing wrong with that vice Mick, it looks just like mine.

I do find that those jaws are pretty useless, some aluminium angle works far better for me.

Richard
Personally I'm not a big fan of soft jaws of any kind, I prefer milled smooth faces; that also presents problems in getting them to mate perfectly flat, even more so on this vice as there are no detachable jaws.

The only way to machine these flat would be to secure the whole vice to the works mill and then run a slot mill down each face.

The other option is to bond some machined steel plates to the cast jaws, they are heavily serrated so an adhesive would bond well, secure said faces together with double sided tape, add adhesive and then clamp tight in vice jaws until adhesive sets. Viola, one set of perfectly flat and mated machined faces.

You're probably right about these, not expensive and supposedly magnetised, they're not....well they are but cheap Chinese magnets I suspect....and it's easy to knock them along the jaw, that will irritate me beyond reason and very quickly too. I expect their life span to be swift and short, I just needed something to get on with, and hold, the larger coach etches.
 

LarryG

Western Thunderer
Many years ago I bought an elderly coach kit that had sides folding up from the floor. I snapped the sides off and formed the tumblehome, narrowed the floor to the correct width, and soldered it all back together. Mine was 4mm, so good luck with this 7mm job.

It's an intriguing set of parts and I assume the coach has an inner and outer body skin where glazing fits between the two?
 

mickoo

Western Thunderer
Small update on the H38, hopefully get the chassis completed tomorrow, it's taking longer than I envisaged :eek:

Just need to 3D print the gas tanks and bracket (1st batch being run up now), some new brake cylinders....the current white metal ones have big slots in the side to fit over the trunnion shaft...:rolleyes: and two new battery boxes; the rest I have.

The bogies are 3rd party supplied so I cannot take any credit for those.

The etch work was rather cleaner, well some flux here and there, until it was washed, bam the Marmite was back, no idea what it is that's causing the muddy tarnish, looks a witch, hate it even though I know it won't be seen once painted. It just looks :shit:

There must be some chemical that makes brass look like brass again, instead of tarnishing it either brown of salmon pink, the usual result of using domestic cleaners.

Dead Bug views.

IMG_9258.jpg

IMG_9259.jpg

IMG_9260.jpg

Right side up and pretty boring, makes you wonder why one goes to all the effort underneath :p

IMG_9261.jpg

Note to self, don't make the under frame beam tabs so long next time, floor material thickness will be fine, then there will be no need to grind back, it'll be covered by the upper body eventually but at this stage, once again, looks :shit:
 

Tim Humphreys ex Mudhen

Western Thunderer
Mick,
I've seen a product called Horolene recommended. It's used by clock makers/restorers to clean brass and supposedly gets rid of tarnishing. The clock expert on the 'Repair Shop' uses it. Available on-line from various sources,I keep meaning to try some out so will order some this week.

all the best
Tim
 

mickoo

Western Thunderer
Mick,
I've seen a product called Horolene recommended. It's used by clock makers/restorers to clean brass and supposedly gets rid of tarnishing. The clock expert on the 'Repair Shop' uses it. Available on-line from various sources,I keep meaning to try some out so will order some this week.

all the best
Tim
Ordered :thumbs:

CousinsUK seem to be the cheapest from a quick web surf.
 

Longbow

Western Thunderer
It's unusual to see a brass cleaner that is alkaline (most are weakly acidic) and contains 5-15% ammonia (which aggressively oxidises brass).
 

Lancastrian

Western Thunderer
Best not store it in the house then:eek:

I think flash point is where it turns from a liquid to a vapour, lighter fluids are even lower.

Even more so if you have a gas hob or boiler ! Don't use it near your micro-gas torch Mick

8d87c31c8818c7f2b82dcf68d4c3102a.png


Ian
 

mickoo

Western Thunderer
Even more so if you have a gas hob or boiler ! Don't use it near your micro-gas torch Mick

8d87c31c8818c7f2b82dcf68d4c3102a.png


Ian
No problems, I've read you need to dilute to use anyway, 7:1 or 8:1 is the recommended ratio, in that format it should....be a touch more stable; but I think the garage is the right place to store and use this stuff....he says having litres of 99.9% IPA and Celly thinners in the house, not forgetting all the fly sprays and domestic cleaners in the house.
 

Deano747

Western Thunderer
Hmmmmm!! I've just ordered a litre. It'll stay in my outside storage shelter!!
Thanks for the info, Ian.

Regards, Rob.
 
Top