7mm Yorky D's Küchentisch - L.94 - a Pannier in proper colours

Discussion in 'Area 51' started by Yorkshire Dave, 30 May 2016.

Tags:
  1. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    I've been meaning to set up another thread for ages to encompass the non-US stuff I've been messing about with in 7mm in between the Cotton Belt GP9 build.

    The starting point are these two multimedia kits (to be built concurrently) from the Furness Railway Wagon Co of Joseph Wright & Sons (later Metropolitan Railway Carriage and Wagon Co.) 4 wheel carriages to build for fun and see what I can do with them.
    Furness 001.jpg

    The kits themselves come in a sturdy corrugated a card box (almost a shoe box) and are quite basic as can be seen below. The resin castings are not high fidelity but I see these kits as a starting point for additional details to make well used and worn out ancient rolling stock.

    The etched parts. Underframe detail, steps, birdcage and roof.
    Furness 003.jpg

    The cast resin parts. Underframe, sides, ends, internal roof supports and a piece of styrene for the floor.
    Furness 004.jpg

    The detail parts. Axleboxes, buffers, oil lamp pots, vents, vacuum pipes, vacuum cylinder, end steps and couplers. In addition there is a length of brass wire and glazing material. OH! and instructions on a mini CD which are okay if you have a computer but if not......
    Furness 005.jpg

    A start was made by cleaning up and washing the resin parts. I glued the luggage third ends and sides together using superglue ensuring all is square. Once set I began filling any gaps and bubbles left in the resin castings with Squadron green putty.

    It was not until I applied the filler primer (Tamiya) I could tell whether I was successful with the initial gap filling. The painted body and photographs reveal more filling to be done.
    Furness 007.jpg
    Furness 008.jpg

    I was not too satisfied with using the green putty as a filler as it is plastic based and does not stick to the resin. Therefore I used a trick I'd seen in Model Railroader - superglue and superglue setting accelerator - so the air bubbles in brake third sides were filled with superglue, accelerator applied and repeated this process until the holes were filled. Once set these areas were filed and sanded smooth.

    The rivets were formed in the underframe overlay etches and these was glued to the underframe casting.
    Furness 006.jpg

    The luggage third so far.
    Furness 010.jpg
     
  2. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    A tad more work a few nights ago.....

    Addition of styrene rod to represent the door hinges.
    Furness 011.jpg


    ....and a start on the third brake.
    Furness 012.jpg
     
    BrushType4, Wagonman, 3 LINK and 5 others like this.
  3. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    I've been messing about with these over the weekend and interiors have been made. Plasticard compartment walls, half height as there was one oil lamp shared between two compartments and wooden seats. Then painting using Vallejo Model Air acrylic paint.

    Here I was trying out something different by shading the nooks and crannies first before applying a coat of zinc green acrylic paint. I also blanked out the windows of the luggage compartment doors with plasticard, superglue and baking powder as the accelerator.
    Furness 013.jpg
    Furness 014.jpg

    After airbrushing the zinc green this turned out to be too light and my experiment above did not work and then decided to paint the carriages Russian green which is almost a dark olive green.

    Before doing this I wanted to create worn paint patches using a technique found in wargaming using marmite, yes marmite (vegemite for those down under), as a mask. The marmite is dabbed on using a scrunched cloth or tissue around the areas prone to wear such as door frames. As I did not have any marmite I used French Dijon mustard instead. The topcoat was airbrushed and one dry I gently wiped the carriage bodies with a damp cloth revealing the zinc green. The droplights were painted with a mix of mahogany and light brown. After this I applied two black/brown washes.

    Furness 015.jpg
    Furness 016.jpg

    The brake carriage has the brake end painted red. This was some SP scarlet I had left over in the airbrush after painting the bloody noses on my SSW GP9 and done before the green was applied.
    Furness 017.jpg

    Then there's the dry brushing to come after I have given these some decals and coat of Alclad matt varnish....
     
  4. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    Although I've temporarily lost interest in my British modelling (having disposed of the bulk of it) I have retained a few items - two vans, a loco and these two coaches.

    I wasn't happy with the green finish I initially applied to the coaches so I stripped them down and started again :eek:.

    This time I airbrushed a whermacht red surface primer and a topcoat of a mixture of the primer and red. Black and brown washes were applied and then finally drybrushed (all paints and washes are from Vallejo). I'm trying to achieve the unkempt run down effect for these 1870s coaches - not quite working at the moment :headbang:.

    While messing about with these I started work on the chassis. Rather than use the bearings in the axleboxes as suggested I instead used the Connoisseur 4 wheel coach compensation units which work a treat. The coaches will form a workmans train for a small private industrial line (yet to be designed and built) set during the 1920's utilising second (third?) hand rolling stock. Just need to find some NBR decals.....

    Brake coach. Yet to receive it's detail parts and roof.
    Furness 024.jpg

    Furness 025.jpg

    Luggage 3rd. Yet to receive it's wheels and detail parts. Furness 027.jpg

    I was trying to make one of the door panels look as if it had been replaced by the new owners - albeit not straight....
    Furness 028.jpg

    .....trying a lifting paint effect and carving corners where the wood has been damaged.
    Furness 029.jpg
     
  5. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    Some more intermittent work on the brake coach roof.

    I pondered for hours how to attach the birdcage to the roof. In the end I tried Mikoo's technique of using a small sliver of solder in order to try a minimum solder construction.

    After cutting the glazing the birdcage frames were soldered to the main roof and clamped on with metal bulldog clips. After this the birdcage roof was soldered on.

    However, my question relating to early carriage roofs is - did they ever have rainstrips?

    The roof.
    Furness 031.jpg
    Furness 030.jpg

    Temporarily on the carriage to see what it looks like.
    Furness 034.jpg
    Furness 033.jpg


    This wagon was a purchase from the O Gauge Guild E&T stand and after checking it over I could see an attempt to was made to weather the vehicle using black paint from a splatter gun.

    In order to remove this I used a cotton wool bud soaked in gunwash (a cellulose thinner/cleaner I believe). This not only removed the black paint but started to remove the lettering and some of the original paint finish from the wagon. As I was going to re-weather the wagon anyway I was not too worried.

    Once I had removed as much as I dare I set applied a Vallejo acrylic dark brown/black wash in order to get into the plank joins. After drying I drybrushed the wagon using various mixtures of dark brown, light brown and black mixed on a palette.

    I then painted in some replacement planks, reapplied the dark brown/black wash and drybrushed again. I finally used a gunwash soaked cotton wool bud to clean the areas around certain lettering and applied a further wash of dark brown.

    SC 01.jpg
    SC 02.jpg
    SC 04.jpg

    SC 06.jpg
    SC 07.jpg
     

    Attached Files:

  6. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    Yet more work, this time rather tedious - cutting and fitting individual window panes for the carriages.

    I have used a CD case cover as I could not find the clear acrylic sheet I ordered and received a couple of months ago.....:rant:. I know it's in the house - somewhere...

    The glazing is tacked in with this glue.
    Glue 1.jpg

    Thus far I have only completed three windows. After fitting I had a go to try and eliminate the translucent/white edge of the pane. To do this I mixed up a wash of PVA and black Vallejo wash and brushed it into the window corners. The compartment nearest the brake end has has this treatment to see what it would look like.
    Furness 038.jpg

    Furness 036.jpg

    The birdcage was also glazed.... a bit messy though but this will disguised by weathering. After all these carriages are for a workman's train.
    Furness 040.jpg

    Before glazing I fitted the grab handles and used Laurie Griffin MR/GW drop door handles. For the luggage compartment I also made a door handle.
    Furness 037.jpg

    Furness 041.jpg

    ....and finally the roof received some attention. I may add some repair patches. This is still a bit shiny at the moment but once the carriage is complete it will receive a coat of matt varnish.
    Furness 039.jpg

    Not the most logical approach to carriage building but I enjoy messing about constructing these in my own way :).
     
  7. mickoo

    mickoo Western Thunderer

    Like the canvas roof effect, really....effective :thumbs::D
     
  8. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    This is toilet paper (obtained from work as they are longer than the usual domestic sheets) pared to single ply and soaked onto the brass roof with superglue.
     
    allegheny1600 likes this.
  9. Peter Insole

    Peter Insole Western Thunderer

    Well done indeed with that gorgeous roof canvas!

    How many times when trying to stick something smooth with thin material, it all goes wrinkly, yet every time I have tried to deliberately obtain that effect it resolutely refuses to stay creased and dries completely flat?!

    Pete.
     
  10. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    This is what I tried to do. It looked smooth until I applied a bit of paint and dry brushing this was the result. It's a case of leave well alone now.
     
  11. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    The tedium of making and fitting the glazing for the carriages is over :) and are for all intents and purposes completed.

    Apologies for the picture quality as these were taken with my tablet. My main camera is out of action as the lens is broken. I either need to get a new lens or a new camera. The latter more than likely as technology has moved on (I quite fancy the Olympus PEN series so I can use my existing 35mm OM lenses).

    Furness 051.jpg

    I could not find any commercial carriage end steps or lamp irons. So I made up the end steps from etched chequer plate to the dimensions of an LBSCR end step I found in one of my books. The lamp irons are actually SR loco lamp irons from Laurie Griffin. I just bent them around a bit.
    The steps, grab irons handrail and tips of the lamp irons were dry brushed with gunmetal to represent wear.
    Furness 044.jpg

    Luggage 3rd
    Furness 042.jpg

    Furness 043.jpg

    Brake 3rd
    Furness 050.jpg
    Furness 052.jpg

    The carriages were zapped with matt varnish, windows cleaned afterwards with IPA on a cotton wool bud and then given a brown wash.

    After seeing the photographs I'm thinking I should make the dirt in the corners black rather than light grey. The buffer heads also need a touch of grease.

    And finally the roofs.
    Furness 045.jpg
    Furness 046.jpg
    .... all ready for workman train service. Just need and industrial loco.......:)
     
  12. Mr Grumpy

    Mr Grumpy Western Thunderer

    Very nice work :thumbs: The painting and weathering is, to me at least very subtle and I love the roof canvass. I'm going to have a go with that one!
    Was the super glue the very runny type or the more thick variety?
     
  13. mickoo

    mickoo Western Thunderer

    Nice weathering :thumbs:

    MD
     
  14. Ressaldar

    Ressaldar Western Thunderer

    +1:thumbs::thumbs::thumbs:

    cheers

    Mike
     
  15. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    I used Zap a Gap medium. Neither too runny or too thick.
     
  16. Steph Dale

    Steph Dale Western Thunderer

    That is, of course, the reason you're known as 'Goldilocks' to your friends...

    :D

    Steph
     
  17. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    As an interlude I built the, dare I say, the Peco hut.

    (Again, my tablet was used to take the photographs which unfortunately does not have sophisticated exposure settings)

    Hut 01.jpg
    Hut 02.jpg
    Hut 03.jpg
    Hut 04.jpg

    The kit itself is plastic injection moulded and took all of 10 minutes to build the shell. However before building I wire-brushed the four walls 1. to provide a keying surface for the paint and 2. to provide some texture to the bricks.

    All the paints used are Vallejo acrylics apart from the matt varnish which was Alclad.

    The shell was painted with Wehrmacht red brown and the odd few bricks painted in various shades of a red/brown mix. Once dry I applied a mixed some Mig volcanic ash grey pigment with a drop of water and IPA and washed this over the building. After drying this was wiped off leaving the pigment in the mortar courses.

    This process also removed some of the paint from the edges of the protruding bricks and a brown wash was applied to the shell which also darkened the mortar joints. I then applied some more pigment mix over odd parts of the building to imply mortar repairs.

    The roof as supplied represents a felt roof. I wanted to try out the Vallejo sandy paste to see if I could make the roof appear as if it was roughly cast from concrete. The sandy paste was applied to the roof and allowed to set. Once set, I roughly sandpapered it to remove the high points then painted it with a mixture of buff, middlestone and stone grey followed by a brown wash. Once dry it was then dry-brushed with a mixture of buff and middlestone to accentuate the remaining high points.

    The door was painted grey, followed by a brown wash then dry-brushed with a faded green and old wood colour. Ironwork was painted a black brown colour and the window frames were also painted faded green.

    The whole ensemble received a coat of matt varnish. After which I then lightly dry-brushed using mixtures of reds, browns and buff. The final dry-brush application was downwards with a middlestone/buff mix to pickup the top edges of the protruding bricks and window ledge.

    All that remains is the 'tidying up' weathering such as soot, algae streaks (for north face of building).
     
    Rob Pulham and David Varley like this.
  18. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    Just need 3 bears (Steiff of course) to share the porridge...... :p
     
  19. Steph Dale

    Steph Dale Western Thunderer

    Dave,
    I've just had a proper look at the Stephenson Clarke wagon and knowing what you started with, that's a superb job. When I get the chance I'll pick up a few more.
    Keep hold of it for a demo piece for the TC, when the time comes up grab it from you.
    Really lovely job mate, it's great see some different techniques for weathering.
    Steph
     
  20. Yorkshire Dave

    Yorkshire Dave Western Thunderer

    I took delivery of this yesterday - the Minerva RTR O scale Kerr Stuart Victory 0-6-0T locomotive I ordered at Telford earlier this year - In my view at £250 it's cheaper than building one.

    Overall a pleasing model of an industrial loco (which have a charm of their own). I intend to finish mine in EKR livery although this was one of the options I could have selected.

    This is the non DCC version as I already have an ESU Loksound decoder in stock which will be fitted in due course.

    It weighs in at 1.05 kg and has a plastic body on a metal chassis.

    KS Victory 01.jpg
    KS Victory 02.jpg
    KS Victory 03.jpg

    It has a standard NEM 8 pin decoder socket. KS Victory 04.jpg
    KS Victory 05.jpg

    Two bags of extras- Etched builders plates for all 10 members of the class and lamp irons, cylinder drain cocks, optional tank vents and sand boxes, three pairs of GW tool boxes and optional front steps. KS Victory 06.jpg

    Cab detail KS Victory 07.jpg
    KS Victory 08.jpg

    Underside KS Victory 09.jpg
     
    BrushType4 and allegheny1600 like this.