V2 4 wheel parcel van1/32 and G3

michael mott

Western Thunderer
Thanks Ian, yes I am cogitating about just how to tackle the holes. I am currently thinking about using the same waste chuck centered on the rotary table. That way I only have to set up once regarding concentricity. But before that I need to finish up the edge of the backside of the hub which I can pop out and just chuck up in a collet.
The bigger challenge is dividing 360 by 16 without a dividing head, my old 10 inch rotary table would have been easier to use but I gave it to my brother in Vancouver, and my little 4 inch one is really basic. I think that perhaps doing set of 8 first the being really careful and resetting half way between 2 holes and doing the second set might be the best.
Michael
 

JimG

Western Thunderer
The bigger challenge is dividing 360 by 16 without a dividing head, my old 10 inch rotary table would have been easier to use but I gave it to my brother in Vancouver, and my little 4 inch one is really basic. I think that perhaps doing set of 8 first the being really careful and resetting half way between 2 holes and doing the second set might be the best.
Michael

Maybe just draw out the angles on paper with successive halving to get the 22.5 degree angle divisions then draw circles to get the centres of the bolts then place drawing on wheel and centre punch through the drawing onto the wheel. Or get yourself a CNC mill or jig borer.
:)

Jim.
 

simond

Western Thunderer
Have you got a smart phone?

They have digital level apps, which I have used when drilling in the lathe, just rest the phone on a jaw and turn chuck to obtain desired reading.

there were photos on RMWeb, but they were lost, unfortunately.
 
Last edited:

Tim Watson

Western Thunderer
It will be interesting to note if the vehicle makes a different sound to conventional metal wheels.

Not sure if I have mentioned it before, but a vicar friend of mine told me that the houses in his parish ((Wolverton) often had paths with triangular wooden sets…

Tim
 

michael mott

Western Thunderer
It will be interesting to note if the vehicle makes a different sound to conventional metal wheels.

Not sure if I have mentioned it before, but a vicar friend of mine told me that the houses in his parish ((Wolverton) often had paths with triangular wooden sets…

Tim
That is interesting I wonder if they were salvaged from wheels or were just a quirky design?
Michael
 

simond

Western Thunderer
I’ve heard this too, apparently it was quite common, though I’ve not seen it.

I wonder if these setts were the offcuts, of which there would be plenty, I guess, and good hardwood too. Too good to burn!
 

simond

Western Thunderer
The wood setts were undoubtedly from scrapped wheels according to Ian (Pusey - S gauge modeller) as he was ministering to retired & active railway workers.

Tim
Thanks Tim, understood, but, assuming* the segments were cut from planks so the grain was radial, there would have been a pair of “half segments” for every segment.

* this is of course a big assumption. I have no idea which way the grain orientation was arranged. It seems most reasonable to believe that they didn’t turn slices of tree into wheels!
 

Jon Nazareth

Western Thunderer
After finishing up the outside rings the hubs were glued into the center of the wheels, then drilled to take the 00x90 countersunk bolts. I machined the bolts but cheated and purchased the nuts.
View attachment 214029 The front and back of the completed wheels.
View attachment 214030
Michael
Gosh, Michael, they are even better than the ones that I made up. :D
Excellent work as always.

Jon
 

michael mott

Western Thunderer
Almost all the frame parts are made now
IMG_2351.jpeg
Set up my mini hand drill on the big mill to put th holes in all the pieces.
IMG_2350.jpeg
Next cut up the right angle bracket stared out with the jewelers saw, but decided to cut them mechanically so got out my little homemade saw table for my lathe a fiddle job to set up. If I were to make one again I’d probably make it differently.
IMG_2352.jpeg
After the first one flew across the room as the cut finished I set up’s clamp so that they stayed put. Slower but safer.
IMG_2353.jpeg
Ten done six more To go then all the angled ones.
IMG_2354.jpeg
Lunch time.
Michael
 

michael mott

Western Thunderer
The second drawing is (also) for a Narrow Gauge Open Carriage Truck, the drawing is dated 1887 for lot 419.

View attachment 171467

View attachment 171479

View attachment 171480


View attachment 171482


Here some enlargements of the brake parts.

View attachment 171483
View attachment 171484

View attachment 171485

View attachment 171486

View attachment 171487


View attachment 171488


regards, Graham
Graham as I am closing in on the assembly of the frames it just occurred to me that the leaf springs appear to be threaded through all the frame angles. In the event of a spring break how would the spring be removed and replaced?
Michael
 
Top